Metal protection

Metal Protector HD

The heavy build grade. It protects like the MD does, but it also leaves a high gloss finish, which is what lets extremely damaged mullions be made to look new rather than merely sealed.

Coverage
50 to 100 sq ft / quart
Lasts
3 to 5 years at least
Finish
High gloss
Full cure
48 hours / no liquids
Presto Metal Protector HD, one quart bottle

Documents

Product data sheet (PDF)
Shared with Metal Protector MD

Safety data sheet (PDF)

Order

You will also need

Adhesion is everything with this one, and surface preparation is where it is won or lost. It also goes on like paint, so the applicator decides the finish.

  • Metal ReSurfacer$55.85
  • Fine grit sandpaper or a solvent wipeNot supplied
  • HPLV sprayer, for the gloss finishNot supplied
Warning

This product carries the signal word Warning on its safety data sheet, not Danger, which is why its info chart reads User Friendly: No. Unlike Metal Protector MD it is water based and it is not flammable. The hazard is respiratory and it comes from the solvent in the formulation.

What to know

  • It may cause respiratory irritation, drowsiness or dizziness. Both are category 3 effects on the safety data sheet. Ventilation matters, and a chemical respirator mask is worth having if you are spraying rather than brushing.
  • It is not flammable and it is water based, so the rag precautions that apply to Metal Protector MD do not apply here.
  • Surface preparation decides whether this works. If contaminants are left on the metal, adhesion is compromised. Fine grit sandpaper or a solvent wipe is how the surface gets ready.
  • If EnviRestore MSR was used to restore the metal, the temporary protection it leaves must be solvent-wiped off first.
  • Nothing wet may touch the surface for 48 hours while it cures.
  • Protect any surface you do not intend to coat, and always test an inconspicuous area first.

Required protection

  • Gloves
  • Goggles
  • Chemical respirator mask, if spraying
  • Ventilation

Open the safety data sheet

HD or MD, and why the coverage differs so much

There are two grades of Metal Protector and they cover wildly different areas per quart. That is not a misprint. One is a thin invisible shield, the other is a heavy gloss coat, and they answer different questions.

Heavy build · you are here

Metal Protector HD

50 to 100 sq ft per quart. A heavy acrylic coat that leaves a high gloss finish. The appearance of the metal is improved, not just preserved, which is how extremely damaged mullions are made to look new.

Thin film

Metal Protector MD

800 to 1,250 sq ft per quart. Roughly sixteen times more area from the same quart, because it goes on thin and invisible. Silicone rather than acrylic, and the one to use when the metal should look untouched.

View Metal Protector MD

Before either one

Metal ReSurfacer

Restore the metal first. Preparation is crucial to adhesion here, more so than with the thin film grade, because a heavy coat on a dirty surface fails visibly.

View product
Then maintenance. Once protected, metal can usually be cleaned with deionized water alone. Contamination settles on the coating rather than the metal and lifts off during ordinary window cleaning.

How to apply it

  1. 1

    Restore the metal first

    For best adhesion and protection, restore the surface with Metal ReSurfacer. Preparation is crucial to proper adhesion, and can be achieved with fine grit sandpaper or a solvent wipe.

  2. 2

    If you used EnviRestore MSR, wipe it off

    That product leaves a temporary protection of its own on the surface. It is important that it is removed with a solvent wipe before this coating goes on.

  3. 3

    Make sure nothing is left on the metal

    All product residues must be completely removed before application. If contaminants are not removed, the adhesion of the protector is compromised. Protect unintended surfaces and test an inconspicuous area first.

  4. 4

    Apply it like paint

    Apply with a sponge roller, a paint brush or a sprayer. The application is similar to painting. The product can be diluted with water for spray applications.

  5. 5

    Spray for the gloss finish

    For a highly polished, enhanced surface apply evenly with a fine mist sprayer such as an HPLV sprayer. A fine sponge or paint brush works too, but may leave brush strokes in the finish.

  6. 6

    15 minutes to start, 48 hours to finish

    The coating begins to cure within 15 minutes and does not fully cure for 48 hours. No liquids may contact the surface during that time.

Equipment needed

  • Gloves and goggles
  • Absorbent microfiber or disposable towels
  • Application sponge roller or brush
  • Optional: HPLV sprayer and chemical respirator mask

Brush or spray

This is the choice that decides how the facade looks when you leave. A sprayer gives the highly polished result the product is capable of. A brush is quicker to mobilise but the strokes can show in a gloss coat.

Technical details

Metal Protector HD
Coverage50 to 100 sq ft per quart
Sold as1 quart bottle, or a 12 quart case
Service lifeAt least 3 to 5 years, depending on environmental conditions and how often the surface is maintained
ChemistryHigh-performance acrylic
SolventWater based
FlammableNo
User friendlyNo carries the signal word Warning on the safety data sheet
Economically efficientYes
Environmentally friendlyYes
ColourMilky white, dries crystal clear
SmellUnique
FinishHigh gloss. For invisible protection use Metal Protector MD instead.
CureBegins within 15 minutes, full cure at 48 hours, no liquids during that time
DilutionCan be diluted with water for spray application
Suitable surfacesAnodised aluminium including window mullions, aluminium composite panels, and painted or coated architectural surfaces
MaintenanceIn most cases deionized water alone
Warranty terms in full

The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful consideration should be made when selecting its suitability for each surface.

The information provided should never be substituted for individual testing to ensure the compatibility of the product with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or in writing.

Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product.