Home » Our Products » Architectural Window Glass Stain & Scratch Removal Products » Glass Protection Products » Glass Defender® HD
GLASS DEFENDER® HD
GLASS DEFENDER® HD
High-performance, invisible coating that protects glass from damaging elements and prevents scratching for up to 10 years
Intended Use
The Glass Defender® Series is designed for all glass surfaces including plate or tempered glass. This product is not suitable for use in areas where food may come in contact with the protected glass.
Recommendations
Product Information
Glass Defender HD will also help to protect glass from stains resulting from adjacent oil-laden stone, such as precast that has been sealed with organic water repellents (i.e. 40% silane).
ADVANTAGES
- Specifically designed for architectural glass surfaces
- Protects glass from stage 1 and 2 corrosion, stains and water erosion
- Helps reduce scratches
- Provides the longest lasting glass protection available
- Excellent beading capabilities
- Invisible protection
- Allows windows to be cleaned using only deionized water
- Inorganic polymers resist aging
- Won’t fade, crack or peel
- Helps to prevent costly restoration
- Gloves and goggles
- Microfiber towels
- Application sponge
- Window cleaning bucket
- Clean, dry window cleaning brush or squeegee
Use protective gear, and prevent personal contact with these products. Do not apply this material to glass when surface temperatures are above 122°F or below freezing.
Never apply this product with an applicator that has been used with other products or solutions, and especially not with soap or water. The surface must be dry and clean from all debris.
Shake and mix product vigorously. Apply Glass Defender products with a spray bottle or sponge. Use the sponge to thoroughly work the product into the surface of the glass. Spread product in a circular, over-lapping motion to ensure product coats entire surface. For best results, thoroughly work the product into the surface so that it forms a cloudy film. Polish the surface with a microfiber towel to remove excess residue. A multi-step fold process should be used for best results. Fold the towel into squares using a clean area of the rag every couple of minutes until excess material has been removed. Leave as much residue as possible while achieving the desired level of clarity. Material residue may not be seen on the glass unless viewed in direct sunlight. Never attempt to clean the residue with water or any type of cleaning solution for a period of 72 hours.
If a second coat is required. The second application should be performed with a clean and dry window cleaning brush and squeegee. Use the window cleaning brush to apply the product. Before the material dries on the glass, a dry window cleaning squeegee can be used to remove excess material. If the material starts to dry, add more product to loosen the dry material for easy removal with the squeegee. This application may eliminate the need for polishing the window. Clean excess residue from edges and frames with a rag. When using a squeegee to remove product, carefully capture excess material with the product applicator. This technique should only be attempted by an experienced window cleaning professional with advanced squeegee skills. Also, this process is only suitable for the second application. Perform subsequent applications immediately after the first. If area is not completely covered, untreated areas may be noticeable as the glass ages and stains develop there.
The product will start to cure within 1 hour. The protective coating will not fully cure for 72 hours. No liquids may come into contact with the glass during that time.
Any wet rags that are laden with material may be flammable. Special precaution should be taken to protect these items from exposure to an ignition source.
SURFACE PREPARATION
Protection performance warranties are contingent upon using either Presto’s EnviRestore® Glass Stain Remover or Glass ReSurfacer® Final Polish to prepare the glass surface immediately prior to the application of Glass Defender products. Remove all dirt from the surface. The level of protection will be sacrificed if all contaminants are not removed prior to use. Be sure to polish the glass surface with a rag to remove all restoration product residues. Do not use detergents on the glass between the restoration and the application of Glass Defender products. Apply the product immediately after the glass restoration process has been completed.
COVERAGE RATES
1,250 sq. ft. per quart; 5,000 sq. ft. per gallon
Glass Defender HD Product Info Chart | |
Water Based | No |
Combustible | Yes |
User Friendly | No |
Economically Efficient | Yes |
Environmentally Friendly | No |
Color | Clear |
Smell | Petroleum |
- Combination of products selected
- Strict adherence to the application instructions
- Exposure to damaging environmental conditions