EnviRestore Glass Stain Remover
An acid-free restorative cream that takes stage 1 corrosion and stubborn staining off glass, by hand or by machine, with no harsh chemistry.
- Coverage
- 250 to 500 sq ft / quart
- Applies
- By hand or by machine
- Removes
- Stage 1 corrosion
- Shelf life
- 3 years
Order
You will also need
This is a cream, not a liquid, and it needs something to work it over the glass. By hand or by machine both work.
- Sponge, soft towel or white non-abrasive padBy hand
- Foam padBy machine
- Gloves, goggles and a microfiber towelNot supplied
Not sure how much the job takes? Work it out below
This product carries no signal word on its safety data sheet, which is why its info chart reads User Friendly: Yes. It is acid-free, non-toxic and water based. The two things to watch are the dry dust and the pressure you put on the glass.
What to know
- Do not inhale the dry dust. On oily stains the residue is deliberately left to dry to a white powder before being removed, and that powder should not be breathed in.
- Do not use excessive pressure. Too much and it causes minor scratching, which only shows when the glass is viewed in direct sunlight.
- The applicator pad or towel must not be contaminated with abrasives. That is the other way this product scratches glass.
- Clean the surface first and remove any dirt or sand that could scratch the glass.
- Always test a small, inconspicuous area in direct sunlight before you start.
- This removes stains sitting on the glass. It does not repair damage already done to the glass by corrosion. For that, and for a distortion-free result, the Glass ReSurfacer System is the right tool.
Where this sits in the glass system
This is the lighter of Presto's two routes to clean glass. It lifts what is sitting on the surface. It does not repair the surface itself, and that is the line between this and the ReSurfacer System.
Restore · you are here
EnviRestore Glass Stain Remover
250 to 500 sq ft per quart. Stage 1 corrosion, mineral deposits, soap scum, exhaust, oils, waterproofing overspray and leaching. Acid-free and applied by hand or machine.
Restore · the heavier route
Glass ReSurfacer System
Where the glass itself is damaged rather than dirty: stage 2 corrosion, scratches and etching. It is a machine process and it leaves no optical distortion, which this product cannot promise.
View Final PolishProtect · either route
Glass Defender
Seals the restored glass for five years. This product is a good preparatory step for it, as long as no oily surfactant detergent is used on the glass in between.
View productHow to apply it
- 1
Clean and test first
Clean the surface before you use this. Remove any dirt or sand that could scratch the glass, and make sure the pad or towel you are about to use carries no abrasives. Test a small, inconspicuous area in direct sunlight.
- 2
By hand
Apply a small amount of product to a sponge, a white non-abrasive pad or a soft towel. Agitate it on the surface until the stain lifts, then wipe away the excess residue. Do not use excessive pressure, or you will cause minor scratching.
- 3
Or by machine
Apply a small amount to a foam pad and work it over the surface until the stain lifts, then wipe away the excess. The same caution applies: excessive pressure causes minor scratching.
- 4
For oily stains, let it dry
Apply the product and let the residue dry to a white powder, then remove the white material with a dry towel or a white non-abrasive pad. Do not inhale the dry dust.
- 5
Repeat if it needs it
A second or third application is sometimes required. That is normal on heavy buildup rather than a sign the product is not working.
- 6
If Glass Defender is going on next
Do not use oily detergents containing surfactants to clean the surface afterwards. They leave a residue that stops the protective coating bonding properly.
Equipment needed
- Gloves and goggles
- Microfiber towel
- Sponge, soft towel or white non-abrasive pad, if applying by hand
- Foam pad, if applying by machine
What it will not do
It removes stains caused by foreign material on the glass. It will not repair damage already done to the glass surface by corrosion. Where the glass itself is etched or scratched, the ReSurfacer System is the tool, because it is the one that leaves no optical distortion.
Technical details
| Coverage | 250 to 500 sq ft per quart, depending on the level of staining |
|---|---|
| Sold as | 1 quart bottle, or a 12 quart case |
| Applied | By hand, or by machine with a foam pad |
| Solvent | Water based |
| Flammable | No |
| User friendly | Yes no signal word on the safety data sheet |
| Economically efficient | Yes |
| Environmentally friendly | Yes |
| Acid free | Yes |
| Colour | White |
| Smell | Pine |
| Shelf life | 3 years |
| Suitable surfaces | Plate and tempered glass. Often works on aluminium and other exterior architectural surfaces. |
| Removes | Stage 1 corrosion, calcium, lime, lime run and lime scale, magnesium, rust, salts, efflorescence, hard water deposits, soap scum, oils and grease, acid rain, adhesives, caulking and coating residue, stone sealer and waterproofing overspray, GFRC leaching, exhaust stains, oxidisation and everyday buildup |
| Will not do | Repair damage already caused to the glass by corrosion |
Warranty terms in full
The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful consideration should be made when selecting its suitability for each surface.
The information provided should never be substituted for individual testing to ensure the compatibility of the product with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or in writing.
Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product.
