Metal protection

Metal Protector MD

A silicone shield that keeps water and oxygen off restored metal, invisible once it is on, and good for up to five years. This is the thin-film grade, the one that covers ground quickly.

Coverage
800 to 1,250 sq ft / quart
Lasts
Up to 5 years
Finish
Invisible
Do not disturb
24 hours
Presto Metal Protector MD, one quart bottle

Documents

Product data sheet (PDF)
Shared with Metal Protector HD

Safety data sheet (PDF)

Order

You will also need

The metal has to be restored before this goes on, or the coating will not adhere properly. Which restorer you used decides how you prepare the surface.

  • Metal ReSurfacer$55.85
  • Solvent wipe, if you used EnviRestore MSRNot supplied
  • Sponge roller or brush, and absorbent towelsNot supplied
Danger

This is the solvent based protector and it carries a signal word on its safety data sheet, which is why its info chart reads User Friendly: No. It is flammable, and rags soaked in it stay a fire risk after the job is over. Metal Protector HD is the water based grade and is not flammable.

What to know

  • Wet rags laden with this product may be flammable. Keep used rags away from any ignition source and dispose of them deliberately rather than leaving them bundled on site.
  • It is solvent based with a petroleum odour. A chemical respirator mask is listed as optional equipment, and is worth having if you are spraying rather than wiping.
  • Protect any surface you do not intend to coat. Overspray and runs on adjacent materials are not easily undone.
  • Nothing should disturb the coated surface for 24 hours.
  • Always test a small, inconspicuous area before committing to an elevation.

Required protection

  • Gloves
  • Goggles
  • Chemical respirator mask, if spraying
  • A deliberate plan for disposing of used rags

Open the safety data sheet

MD or HD, and why the coverage differs so much

There are two grades of Metal Protector and they cover wildly different areas per quart. That is not a misprint. They are built to do different jobs, and ordering the wrong one is an expensive mistake in either direction.

Thin film · you are here

Metal Protector MD

800 to 1,250 sq ft per quart. A thin, invisible silicone shield for metal that is in reasonable condition. It covers a lot of ground per quart because it goes on thin and is meant to be unnoticeable.

Heavy build

Metal Protector HD

50 to 100 sq ft per quart. Roughly sixteen times less area from the same quart, because it lays down a far heavier coat. That is what lets extremely damaged window mullions be made to look new again.

View Metal Protector HD

Before either one

Metal ReSurfacer

Restore the metal first. If contaminants are left on the surface, the protector's ability to adhere is compromised and the five years does not happen.

View product
Then maintenance. Once protected, metal surfaces can usually be cleaned with deionized water alone. The coating forces stain-forming contamination to settle on the coating rather than on the metal, so it lifts off during ordinary window cleaning.

How to apply it

  1. 1

    Restore the metal first

    For best adhesion and protection, restore the surface with Metal ReSurfacer beforehand. Contaminants left on the metal compromise how well this product can grip it.

  2. 2

    If you used EnviRestore MSR, wipe it

    EnviRestore MSR leaves a temporary protective layer of its own. Use a solvent wipe to take that off and prepare the surface, or this coating goes onto the wrong thing.

  3. 3

    Mask and test

    Protect any surface you do not intend to coat. Always test a small, inconspicuous area before going further.

  4. 4

    Work it in, invisible finish

    Apply with a sponge or rag, spreading in a circular overlapping motion with multiple strokes so every inch of the metal is worked. Once the area is completely covered, use an absorbent rag or towel to remove the excess residue and dry the surface.

  5. 5

    Or lay it wet, for superior protection

    For superior yet still invisible protection, apply the product so the surface is evenly wet and leave it to dry rather than wiping it back.

  6. 6

    Leave it 24 hours

    Do not disturb the surface for 24 hours. And deal with the rags: anything soaked in this product may be flammable and needs keeping away from ignition sources.

Equipment needed

  • Gloves and goggles
  • Absorbent microfiber or disposable towels
  • Application sponge roller or brush
  • Optional: HPLV sprayer and chemical respirator mask

Afterwards

In most cases protected metal can be cleaned with deionized water alone. That is the point of the coating: contamination settles on it rather than on the metal, and comes off during normal maintenance.

Technical details

Metal Protector MD
Coverage800 to 1,250 sq ft per quart
Sold as1 quart bottle, or a 12 quart case
Service lifeUp to 5 years, depending on environmental conditions and how often the surface is maintained
SolventSolvent based
FlammableYes
User friendlyNo carries a signal word on the safety data sheet
Economically efficientYes
Environmentally friendlyNo
ColourClear
SmellPetroleum
CureDo not disturb the surface for 24 hours
Suitable surfacesAnodised aluminium including window mullions, aluminium composite panels, and painted or coated architectural surfaces
How it worksHigh-performance silicone shields the metal from water and oxygen, so stain-forming contamination settles on the coating rather than the metal
MaintenanceIn most cases deionized water alone
Warranty terms in full

The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful consideration should be made when selecting its suitability for each surface.

The information provided should never be substituted for individual testing to ensure the compatibility of the product with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or in writing.

Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product.