Stone protection

Leach Stop

A clear, breathable sealer that stops precast, GFRC, concrete and natural stone from leaching minerals down onto the glass and metal below. One coat, invisible, and it holds for up to ten years.

Coverage
250 to 500 sq ft / gallon
Protects for
Up to 10 years / one coat
Base
Solvent / not water based
Sold as
5 gallon pail / approx 35 lbs
Presto Leach Stop in a five gallon pail

Order

You will also need

Leach Stop goes on last, over a surface that is already clean, rinsed and dry. Anything left behind on the stone gets sealed under it.

  • Low pressure sprayer, roller, brush or lambswool applicatorNot supplied
  • Mineral spiritsFor tool cleanup
  • Rags or towelsTo take off the excess
  • A stone cleanerClean first
Before you start

This is the one product in the stone line that is not water based. Its info chart reads User Friendly: No, which means its safety data sheet carries a hazard signal word. Read the sheet before the first pail is opened, and brief whoever is applying it.

What to know

  • It is combustible and solvent based, with a petroleum smell. Keep it away from ignition sources and give the area ventilation.
  • Tools clean with mineral spirits, not water. Plan for that before you start rather than after.
  • Never apply to a damp or wet surface, or below freezing. Trapped moisture ruins the coat.
  • Do not let the product pool and dry on the surface. Protection comes out uneven and a residue can form. Take the excess off with a rag.
  • Always test a small, inconspicuous area first. Never apply a second coat unless two coats were tested and approved beforehand.
  • Protect any unintended areas. If it dries somewhere it should not have, it takes one of the EnviRestore or Stone Restore products to get it off.

Required protection

  • Protective gear
  • Ventilation, solvent vapour
  • No ignition sources

Open the safety data sheet

Clean it first, then seal it

Leach Stop is the last step, not the first. It seals the surface, which means it seals in whatever is still on the surface. Cleaning comes first, then a thorough rinse, then this.

Step one · mineral stains

Stone Restore HD

Efflorescence, rust, red clay and iron staining, on rough and polished surfaces alike.

View product

Step one · biological stains

Stone Restore CB2

Mould, mildew and algae. Often used alongside HD when a facade carries both kinds of staining.

View product

Step two · you are here

Leach Stop

Once the stone is clean, rinsed and dry, one coat seals it. It fills the microscopic cracks the water was travelling through, which is what stops the leaching onto the glass below.

Why this matters on a high rise. Untreated precast carries minerals down the face of the building every time it rains, and they land on the glass and the window frames. Sealing the stone is what keeps the glass restoration you just paid for from having to be done again.

How to apply it

  1. 1

    Finish the caulking first

    Complete all caulking and surrounding construction work before this product goes on. Newly installed stone or grout has to be allowed to cure first.

  2. 2

    Clean, rinse, and let it dry

    The stone must be completely clean and free of dirt, staining and biological growth. Rinse thoroughly so no cleaning product is left on the surface, because anything left behind interferes with the coating. Never apply to a damp or wet surface, or below freezing.

  3. 3

    Test an inconspicuous area

    Always test a small, out of the way area before you commit to the elevation.

  4. 4

    Apply full strength, one even coat

    Low pressure sprayer, roller, brush, sponge or lambswool applicator, and it can be back rolled. Do not dilute. Let it saturate the surface, but do not let it pool and dry, or the protection comes out uneven and a residue can form. Take the excess off with a rag or towel.

  5. 5

    A second coat only if it was tested

    Porous, absorbent surfaces may need a second coat, applied the same way while the first is still drying. Never apply a second coat if two coats were not tested and approved beforehand.

  6. 6

    Let it cure

    Protection begins as soon as it dries. Full water and stain protection takes 24 to 72 hours, and the surface should be kept clear of water for at least 48. Application rate, temperature and humidity all move those times.

  7. 7

    Clean up with mineral spirits

    Tools and equipment clean with mineral spirits. If the product dried on an adjacent surface, EnviRestore Glass Stain Remover, EnviRestore MSR, or Stone Restore HD, CB2 or PS will take it off depending on the material.

Equipment needed

  • Protective gear
  • Low pressure sprayer, roller, brush, sponge or lambswool applicator
  • Mineral spirits
  • Rags or towels

Keeping it clean afterwards

A mild stone cleaner in heated, deionised water, left a minute or two, then rinsed off at very low pressure. A soft brush for anything stubborn.

On exterior vertical surfaces Presto suggests a maintenance clean every two to three years. High pressure is not needed and can damage the coating. This is a recommendation, not a condition of the warranty.

Technical details

Leach Stop
Coverage, architectural materials250 to 500 sq ft per gallon, which is 1,250 to 2,500 per 5 gallon pail. Concrete, precast, cast in stone, stucco, terrazzo and natural stone.
Coverage, masonry and grout250 to 400 sq ft per gallon, which is 1,250 to 2,000 per pail. Brick, pavers, block, burnished block and split-face block.
Coverage, tile and grout500 to 1,200 sq ft per gallon, which is 2,500 to 6,000 per pail. Mexican, unglazed, clay, terra-cotta, quarry, ceramic and porcelain tile.
Sold as5 gallon pail, approximately 35 lbs
Protects forUp to 10 years
CoatsOne, full strength, undiluted. A second only on porous surfaces and only if two coats were tested first.
Cure timeProtection starts on drying. 24 to 72 hours for full water and stain protection. Keep water off for 48 hours.
OrientationHorizontal or vertical. Horizontal surfaces may need reapplication sooner.
Water basedNo, solvent based
CombustibleYes
User friendlyNo the safety data sheet carries a signal word
Economically efficientYes
Environmentally friendlyNo
ColourClear
SmellPetroleum
Active ingredientsA blend of silicone, quartz and fluoropolymers
CleanupMineral spirits
Protects againstDust and dirt, mildew, mould, algae, soap scum, exhaust, efflorescence, mineral deposits, rust, red clay, waterproofing leaching and food stains. Not caulking residue, oil or grease.
Warranty terms in full

The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful consideration should be made when selecting its suitability for each surface.

The information provided should never be substituted for individual testing to ensure the compatibility of the product with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or in writing.

Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product.