Stone restoration
Stone Restore CB2
A compounded-strength chlorine bleach for the living side of the problem: green and black algae, mould and mildew. Stronger than anything sold at retail, and it always goes on diluted.
- Stains
- Biological / algae, mould, mildew
- Chemistry
- Chlorine bleach / water based
- Dilution
- Always / 1:3 at the strongest
- Sold as
- 5 gallon pail / concentrate
Order
You will also need
This never goes on neat, so the water supply is part of the job. Nothing else goes in the tank with it.
- Chemical resistant sprayer, 40 psi maxNot supplied
- Running water on siteKeep the surface damp
- Pressure washer, 40 or 25 degree tipOptional, for rinsing
- Stone brushOptional
- Leach StopTo protect afterwards
Not sure how much the job takes? Here is why we would rather talk it through
Before you start
This is chlorine bleach at a strength that is not sold at retail. Its info chart reads User Friendly: No, which means its safety data sheet carries a hazard signal word. Read the sheet and brief the crew before the first pail is opened.
What to know
- Never mix this product with any other chemical. That includes Stone Restore HD, which is acidic. If a facade needs both, rinse the surface completely clean between them rather than letting the two meet.
- It is always diluted. One part product to three parts water is the strongest the data sheet allows. It is never applied neat.
- Not for limestone, marble or travertine. All three are marked No outright on the suitability sheet.
- Never let it dry on the surface. Keep the area wet, and keep running water on hand.
- Protect everything in the fall zone: pedestrian and traffic areas below, electric tools, fabrics, furniture, fixtures and plants. Bleach and fabric is a short conversation.
- It may cause discolouration on some stone, or affect how well a water repellant bonds later, if used incorrectly. Always test a small, inconspicuous area first.
Required protection
- Protective gear
- Running water on site
- Nothing else in the tank
Which stone product the stain needs
Presto's stone line is split by the kind of stain, not by strength. This one handles what is alive on the surface. Mineral staining takes a different chemistry entirely, and most facades carry some of both.
Biological stains · you are here
Stone Restore CB2
Green and black algae, mould and mildew. A compounded-strength chlorine bleach with scum-free surfactants and degreasers to loosen the dirt and oil underneath.
Mineral stains
Stone Restore HD
Efflorescence, rust, red clay, iron and oxidation. Acidic, so it is the opposite chemistry and never goes in the same tank.
View productPolished stone
Stone Restore PS
Surface contamination on polished stone: soap scum, sealer overspray, calcium and lime. Acid free, by hand, and safe on the limestone and marble this product cannot touch.
View productThen protect it. Presto recommends Leach Stop on the newly restored surface. Algae comes back fastest on porous stone that holds water, which is exactly what sealing it stops.
How to apply it
- 1
Protect everything in the fall zone
Traffic and pedestrian areas below the project, electric tools, fabrics, furniture, fixtures and plants. Then test a small, inconspicuous area before you commit to the elevation.
- 2
Dilute it
One part product to three parts water is the strongest mix the data sheet allows, and most surfaces want weaker. For brick, one part product to nine parts water. For concrete carrying stubborn staining the sheet gives a different starting point, so confirm that one with a Presto representative before you mix it.
- 3
Wet the surface first
Wet the intended surface before any product goes on, and keep running water available to hold it damp.
- 4
Spray an even coat
Low pressure, 40 psi maximum, through a chemical resistant sprayer. Rinse any unintended surface immediately, glass and frames especially.
- 5
Let it work, but never let it dry
Keep the area moistened with product to loosen the soil. For deep stains give it 10 to 20 minutes, and watch it the whole time. A dried surface is the failure mode here.
- 6
Rinse it off
Pressure washer with a white 40 degree tip or a green 25 degree tip, held as far from the surface as you can. No pressure washer, use a brush. Heated deionised water gives the best result.
- 7
Rinse again, then repeat if needed
Rinse thoroughly so nothing is left behind. Heavily soiled, porous or absorbent surfaces often take a second application, immediately after the first and applied the same way.
- 8
Seal it
Presto recommends Leach Stop on the restored surface to hold it for years.
Equipment needed
- Protective gear
- Running water
- Chemical sprayer
- Pressure washer, optional
- Stone brush, optional
What it is actually doing
The bleach kills the algae, mould and mildew so the staining lets go and rinses away with water. The surfactants and degreasers in the blend lift the dirt and oil that the growth was holding onto. That is why the rinse matters as much as the application.
Technical details
| Coverage | Varies by substrate and by how far the product is diluted, so there is no single figure. The data sheet carries a rate for every surface. Talk it through with a Presto representative before you order. |
|---|---|
| Sold as | 5 gallon pail, concentrate |
| Dilution | 1 part product to 3 parts water at the strongest. 1 part to 9 parts for brick. Never applied undiluted. |
| Orientation | Horizontal or vertical |
| Water based | Yes |
| Flammable | No |
| User friendly | No the safety data sheet carries a signal word |
| Economically efficient | Yes |
| Environmentally friendly | No |
| Colour | Yellowish green |
| Smell | Bleach |
| Suitable surfaces | Concrete, precast, cast in stone, stucco, terrazzo, quartz, quartzite, granite, serpentine, slate, sandstone, bluestone, brownstone, flagstone, soapstone, brick, pavers, block, burnished block, split-face block, and tile and grout. Also most painted surfaces. |
| Not suitable for | Limestone, marble and travertine |
| Removes | Dust and dirt, mildew, mould, algae, soap scum, exhaust and food stains. Not efflorescence, mineral deposits, rust, red clay, caulking residue, waterproofing leaching, oil or grease. Those are Stone Restore HD's job. |
Warranty terms in full
The information provided by Presto for the safe and effective use of this product, and all of our products, is believed to be good and accurate. However, due to the many different possible applications of this product, careful consideration should be made when selecting its suitability for each surface.
The information provided should never be substituted for individual testing to ensure the compatibility of the product with each surface intended for use. The purchaser shall assume all responsibility for determining the suitability of this product. When used as intended, this product will perform as stated. No other warranty can be made for this product, verbally or in writing.
Presto warrants this product to be free from defects. In the event this product is found to be defective, we will provide a sufficient amount of product to replace the defective product.
How much will the job take?
There is no calculator on this page, and that is deliberate. Stone Restore CB2 covers anywhere from 150 to 700 square feet per gallon depending on the substrate, and every one of those figures is for the product undiluted. This product is never used undiluted, so the real number depends entirely on the mix the surface calls for.
A figure pulled out of that range would be a guess. Tell a Presto representative the stone, the growth you are dealing with and the square footage, and you will get a real one.
Have the data sheet open when you call. The suitability table in it lists a coverage rate for every one of the thirty surfaces this product is rated against.
